Aquaculture & Marine Electric Titanium Heaters
Massive range of Aquaculture / Aquaponics and Tropical Marine electric heaters perfect for use in sea water Marine applications for spa / pool heating aboard vessels, and tropical fish heating in aquariums
The only metal that water comes into contact with is pure Titanium - tube and element.
Also listed is the Elecro G2 Titanium Heat Exchanger range - again the only metal that secondary fluid (the water to be heated) contacts is pure Titanium. Primary fluid is encased by 316L stainless steel tube.
Electrical safety certificate SAA-142396-EA, SAA-142239
Single Phase Heaters - 4 sizes available 2kw, 3kw, 4.5kw, & 6kw
3 Phase Heaters - 8 sizes available 12kw, 15kw, 18kw, 24kw, 30kw, 36kw, 45kw, & 54kw
Electric Single Phase 240v & Three Phase 415v Stand Alone Spa Heaters
- Easy Installation, floor or vertical wall mount (Titan Optima)
- Super safe operation
- Robust, durable construction
- Digital water flow signal, no pump interlock required
- Low element Watts density reduces encrustation
- Titanium heating elements zero corrosion guaranteed
- Titanium flow tube
- Dual cascade wired Schneider contactors on each element bank
- Digital timers for staged energisation
- Digital thermostat provides more accurate temperature control
- Epoxy coated aluminium cabinet (Titan Optima series)
The Titan Optima heater is manufactured from top quality components and material at the Elecro works in Hertfordshire, England.
Construction consists of three flow tubes which are fitted to the uniquely designed manifold mouldings made from specially formulated polymer alloy material. Spiral wound titanium heating elements provide a 'Vortex' water flow, these are positioned equidistantly along each flow tube, providing ultra efficient performance. The low Watts density of these elements guarantees extended life and reliability. The outlet manifold accommodates a flow switch which provides a digital signal to the control board. The inlet manifold is fitted with a titanium temperature detection pocket, fitted with NTC temperature sensor.
The heater is supported by two G/F polyamide chassis end panel mouldings, these together with durable aluminium panels form an enclosure finished in tough epoxy powder coated paint. The enclosure houses the cascade wired Schneider contactors (two per element bank), timers and control board. The enclosure design encourages induced cooling giving an extended switch gear life span.
The heater control panel is on the top of the enclosure containing the indication and fault lights as well as the digital touch control screen. The unit can be floor or wall mounted and is supplied complete with a bracket for vertical wall mounting offering the simplest and tidiest of installations, even in limited space, thus making it particularly suitable for parallel multi-unit installations.
The Titan Optima heater can be easily operated using the touch screen control panel. The inlet manifold has been designed to minimise flow imbalance between the flow tubes, greatly reducing the risks of air locking. Safety and equipment protection is provided by the highly reliable flow switch, over temperature protection is provided by the four safety thermal cut outs (auto-reset) and a safety thermal cut out (manual reset).
The digital control board allows accurate control of the pool water temperature thanks to its high precision. The blue digital characters on the touch screen are clearly legible, even in bright sunlight.
To reduce voltage drop on start-up, the heater element banks are energised in a staged cascaded sequence, with a time delay between energising each bank.
Optima Compact heaters differ from Titan Optima series heaters in the following ways:
The housing is of Polymer construction.
Optima Compact heaters utilise a single flow tube assembly
1.5" / 40mm plumbing connections - unions included
They do not incorporate the additional delay relays and components, but are otherwise essentially the same control circuit construction and heater flow tube construction.
Element watts density is higher in equivalent rated heater. eg a 24kw Optima Compact uses 3 x 8kw elements. A 24kw Titan Optima utilses 6 x 4kw elements to lower the watts density and thereby increasing element life expectancy.
Heating Elements - Titanium
Flow tubes - Titanium
Cladding panels - Moulded aluminium, epoxy powder coated
ContactorsCascade wired, Duel Schneider contactors per element bank
Digital Control Thermostat0ºC > 40ºC (0.5ºC Differential)
Safety Thermal cut-out55ºC (Manual reset)
Flow Tube Thermal cut-out60ºC (Auto reset) 1 per flow tube
Enclosure Thermal cut-out60ºC (Auto reset)
Flow Switch - Gold tipped reed switch with Titanium fulcrum pin
Wiring - High temperature, silicone sheathed, multi-strand copper conductors
Seals - High temperature special formula EPDM
Water Connections 63-mm Spigot, supplied with 2"/50mm unions
Working Pressure - 4 bar maximum
Mounting - Floor or wall mountable (Titan Optima - wall bracket supplied)
85kw Premium UK manufactured Swimming Pool / Spa thermal titanium heat exchanger system with superior corrosion resistance and efficiency properties - can also be used in Marine and Aquaculture applications....
7 In Stock
122kw Premium UK manufactured Swimming Pool / Spa thermal titanium heat exchanger system with superior corrosion resistance and efficiency properties - can also be used in Marine and Aquaculture applications...
5 In Stock
Xylem Lowara ecocirc BASIC 15-6/130 hot water circulation pump. Speed control knob 1-7 The 7 position dial is used to adjust flow to the correct level to ensure that the temperature differential between inl...
1 In Stock
Xylem Lowara ecocirc PREMIUM 15-6/130 hot water circulation pump with display. The display shows in turn: Power in Watts, Head pressure, and flow rate which assist in correctly setting the pump to the applic...
1 In Stock
Xylem Lowara TLCN 15-6 circulation pump 3 speed basic circulator pump for use with heat exchangers etc. Also suitable for potable water applications - pump is stainless steel High speed - 80w / 6000 litres...
1 In Stock